Question Bank: Turner Theory 1st Year

Question Bank: Turner Theory 1st Year

Turner 1st Year NIMI QB

Module 1 Safety and Hand tools
Q. Which type of vice is used for marking of small jobs on the surface plate? | सरफेस प्लेट पर छोटे कार्यों के अंकन के लिए किस वाईस का प्रयोग किया जाता है?
Correct answer: C
Q. Which is used for filling narrow grooves and angles above 10°? | 10° से ऊपर के संकीर्ण खांचे और कोण को भरने के लिए किसका उपयोग किया जाता है?
Correct answer: D
Q. What will happen if the rake angle of a chisel increases? | यदि एक छेनी का रेक कोण बढ़ता है तो क्या होगा?
Correct answer: A
Q. What is the cut of file used for deburring the job on lathe? | लेथ में जॉब पर से बर हटाने के लिए किस कट की फाइल का प्रयोग किया जाता है?
Correct answer: D
Q. What is the name of the angle marked X? | X चिह्नित कोण का नाम क्या है?
Correct answer: C
Q. What is the point angle of cold chisel to cut aluminium? | एल्युमीनियम काटने के लिए कोल्ड चीजल का बिंदु कोण क्या होगा?
Correct answer: A
Q. Which file is used to make the job close to the finishing size? | जॉब को फिनिश्ड साइज़ के करीब लाने के लिए किस फ़ाइल का उपयोग किया जाता है?
Correct answer: C
Q. Which portion of a hammer head is not hardened or left soft? | हथोड़े के कौन से भाग को कठोरिकृत नहीं किया जाता अथवा नर्म छोड़ दिया जाता है?
Correct answer: C
Q. What is the body material of bench vice? | बेंच वाईस की बॉडी किस सामग्री की बनी होती है?
Correct answer: A
Q. What is use of steel rule? | स्टील रूल का उपयोग क्या है?
Correct answer: C
Q. What is the name of part marked as ‘X’? | ‘X’ द्वारा चिह्नित किए भाग का नाम क्या है?
Correct answer: C
Q. What is the name of the part marked X? | X चिह्नित भाग का नाम क्या है?
Correct answer: A
Q. How to protect the work surface from damage while clamping in the vice? | वाइस में क्लैम्पिंग करते समय जॉब की सतह को नुकसान से कैसे बचाएं ?
Correct answer: B
Q. What is marked as ʹXʹ? | Xʹ के रूप में चिह्नित क्या है?
Correct answer: B
Q. What is the standard colour code used for identifying the bin for the metal waste material? | धातु अपशिष्ट सामग्री के लिए बिन की पहचान के लिए मानक रंग कोड कौन सा है?
Correct answer: A
Q. What is the name of the part of the file marked X? | X चिह्नित फ़ाइल के भाग का नाम क्या है?
Correct answer: D
Q. What is the name of the chisel? | छेनी का नाम क्या है?
Correct answer: C
Q. How the Jaw of the hand vice is opened and closed? | हैंड वाइस का जबड़ा कैसे खुलता और बंद होता है?
Correct answer: D
Q. Which victim has given CPR immediately? | किस पीड़ित को CPR तत्काल देंना चाहिए?
Correct answer: A
Q. Which file is used for filing surfaces at right angle on already finished surface? | पहले से तैयार सतह की समकोण पर सतह बनाने के लिए प्रयोग की जाने वाली फाइल है?
Correct answer: C
Q. Which type of vice has a trigger for opening the movable jaw? | किस वाईस में चाल जबड़े को खोलने के लिए ट्रिगर दिया जाता है?
Correct answer: D
Q. What is the type of the steel rule? | स्टील रूल का प्रकार क्या है?
Correct answer: B
Q. Which one is the golden hours related to first aid? | प्राथमिक चिकित्सा से संबंधित स्वर्णिम समय कौन सा है?
Correct answer: C
Q. Name the part of file marked as “X”. | फ़ाइल के ’X’ के रूप में चिह्नित भाग को नाम दें।
Correct answer: A
Q. Name the part marked as ‘X’ of the file. | फ़ाइल के ’X’ के रूप में चिह्नित भाग को नाम दें।
Correct answer: C
Module 2 Marking tools and Cutting tools
Q. Which safety practice refers, Do not wear the ring? | कौन सा सुरक्षा अभ्यास संदर्भित करता है, अंगूठी न पहनें?
Correct answer: D
Q. How the Jaw of the hand vice is opened and closed? | हैंड वाइस का जबड़ा कैसे खुलता और बंद होता है?
Correct answer: D
Q. How to protect the work surface from damage while clamping in the vice? | वाइस में क्लैम्पिंग करते समय जॉब की सतह को नुकसान से कैसे बचाएं ?
Correct answer: B
Q. Which steel rule is used to measure keyways? | की वे को मापने के लिए किस स्टील रूल का उपयोग किया जाता है?
Correct answer: D
Q. Name the defect that causes the metal chips to clog between the teeth of file. | उस दोष का नाम बताइए जब धातु के चिप्स फाइल के दांतों के बीच घुस जाते है?
Correct answer: B
Q. What is the correct sequence of the operation of a simple fire extinguisher? | एक साधारण अग्निशामक यंत्र के संचालन का सही क्रम क्या है?
Correct answer: A
Q. What is the type of the steel rule? | स्टील रूल का प्रकार क्या है?
Correct answer: B
Q. What is the cut of file used for deburring the job on lathe? | लेथ में जॉब पर से बर हटाने के लिए किस कट की फाइल का प्रयोग किया जाता है?
Correct answer: D
Q. What is the name of the chisel? | छेनी का नाम क्या है?
Correct answer: C
Q. Which file is used to make the job close to the finishing size? | जॉब को फिनिश्ड साइज़ के करीब लाने के लिए किस फ़ाइल का उपयोग किया जाता है?
Correct answer: C
Q. Which type of vice has a trigger for opening the movable jaw? | किस वाईस में चाल जबड़े को खोलने के लिए ट्रिगर दिया जाता है?
Correct answer: D
Q. What is the standard colour code used for identifying the bin for the metal waste material? | धातु अपशिष्ट सामग्री के लिए बिन की पहचान के लिए मानक रंग कोड कौन सा है?
Correct answer: A
Q. Which victim has given CPR immediately? | किस पीड़ित को CPR तत्काल देंना चाहिए?
Correct answer: A
Q. What is the name of the angle marked X? | X चिह्नित कोण का नाम क्या है?
Correct answer: C
Q. What is the use of a Half round nose chisel? | हाफ राउंड नोज छेनी का उपयोग क्या है?
Correct answer: B
Q. What is the name of file? | इस फ़ाइल का नाम क्या है?
Correct answer: B
Q. What will happen if the rake angle of a chisel increases? | यदि एक छेनी का रेक कोण बढ़ता है तो क्या होगा?
Correct answer: A
Q. Which vice is used for holding hollow cylindrical jobs? | खोखली बेलनाकार जॉब्स को पकड़ने के लिए किस वाइस का इस्तेमाल किया गया?
Correct answer: B
Q. What is the name of the part marked X? | X चिह्नित भाग का नाम क्या है?
Correct answer: A
Q. What is the name of the part marked as ‘X’? | ‘X’ द्वारा चिह्नित भाग का नाम क्या है?
Correct answer: D
Q. Which one is the golden hours related to first aid? | प्राथमिक चिकित्सा से संबंधित स्वर्णिम समय कौन सा है?
Correct answer: C
Q. What is the name of the part of the file marked X? | X चिह्नित फ़ाइल के भाग का नाम क्या है?
Correct answer: D
Q. Name the part of file marked as “X”. | फ़ाइल के ’X’ के रूप में चिह्नित भाग को नाम दें।
Correct answer: A
Q. What is the reason for scratches produced on filed surface? | फाइल वाली सरफेस पर खरोंच चिप्स के उत्पादन का कारण क्या है?
Correct answer: A
Q. What is the name of the vice? | वाइस का नाम क्या है?
Correct answer: A
Module 3 Lathe and Its accessories
Q. Which part of the lathe contains the mechanism for moving and controlling the carriage? | खराद के किस भाग में कैरिज को घुमाने और नियंत्रित करने का तंत्र होता है?
Correct answer: A
Q. What is the name of the accessory? | सहायक उपकरण का नाम क्या है?
Correct answer: D
Q. What is the name of part marked as ‘x’ in center lathe? | ‘X’ द्वारा केंद्र खराद का कौन सा भाग चिह्नित है?
Correct answer: B
Q. What is the name of the part of carriage marked as ‘X’? | ‘X’ द्वारा कैरिज के चिह्नित भाग का नाम क्या है?
Correct answer: A
Q. What is the swing over bed? | स्विंग ओवर बेड क्या है?
Correct answer: B
Q. What is the name of the part ‘X’? | भाग ‘X’ का नाम क्या है?
Correct answer: D
Q. Why lathe bed is manufactured by cast iron? | लेथ का बेड कच्चा लोहा से क्यों बनाया जाता है?
Correct answer: A
Q. How many speed will obtained from a 3 stepped cone pulley headstock of lathe with back gear arrangement? | एक 3 कदम शंकु चरखी हेडस्टॉक से, बैक गियर व्यवस्था के साथ खराद की कितनी गति प्राप्त होगी?
Correct answer: D
Q. Where is the dead center fixed on lathe? | लेथ में डेड केंद्र कहाँ स्थापित किया जाता है?
Correct answer: B
Q. Which part of the lathe helps to give angular movement during taper turning? | लेथ का कौन सा भाग टेपर टर्निंग के कोणीय गति देने में कौन सा भाग सहायता प्रदान करता है?
Correct answer: C
Q. Which material is used for marking lathe bed? | लेथ बेड बनाने के लिए किस सामग्री का उपयोग किया जाता है?
Correct answer: C
Q. Which one of following lathe accessory fixed on lathe bed? | निम्नलिखित में से कौन सा लेथ एक्सेसरी लेथ बेड पर फिक्स होता है?
Correct answer: C
Q. Which part of the cone pulley head stock is engaged for reducing the spindle speed? | शंकु पुली हेड स्टॉक का कौन सा हिस्सा स्पिंडल गति को कम करने के लिए लगा हुआ है?
Correct answer: D
Q. What is the name of part marked as ‘x’ in center lathe? | ‘X’ द्वारा केंद्र खराद का कौन सा भाग चिह्नित है?
Correct answer: D
Q. What will happen if the carriage is not being locked while facing in a lathe? | अगर खराद में सामना करते हुए कैरिज को लॉक नहीं किया जा रहा है तो क्या होगा?
Correct answer: A
Q. Which mechanism is also called as reversing gear unit? | किस तंत्र को प्रतिवर्ती गियर इकाई भी कहा जाता है?
Correct answer: A
Q. Which accessory is used in between center work? | किस सहायक उपकरण को केन्द्रों के बीच प्रयोग किया जाता है?
Correct answer: B
Q. What is the name of the part marked ‘X’? | ‘X’ द्वारा चिह्नित भाग का नाम क्या है?
Correct answer: C
Q. How many spindle speed totally obtained from a cone pulley headstock? | एक शंकु चरखी हेडस्टॉक से कितनी गति प्राप्त होगी?
Correct answer: C
Q. Which part of the lathe is ‘H’ shaped cast iron on the bed ways? | लेथ के बेड के ऊपर रखे कौन से ढलवा लौहे के बने भाग का आकार H के समान होता है?
Correct answer: A
Q. Name the lathe accessory shown. | दिखाए गए लेथ एक्सेसरी का नाम बताइए।
Correct answer: A
Q. What is the name of the center accommodates in the main spindle sleeve? | मुख्य स्पिंडल की स्लीव में धारित किए जाने वाले केंद्र का नाम क्या है?
Correct answer: D
Q. Why the ball center is used in taper turning by offset method? | ऑफसेट विधि से टेपर टर्निंग करने में बॉल सेटर का प्रयोग क्यों किया जाता है?
Correct answer: A
Q. What is the name of part marked as ‘X’? | ‘X’ द्वारा कौन सा भाग चिह्नित है?
Correct answer: A
Q. Which work holding device is used to hold irregular shaped work? | अनियमित आकार के कार्यों को पकड़ने के लिए किस कार्य धारण उपकरण का उपयोग किया जाता है?
Correct answer: C
Q. What is the name of the center? | केंद्र का नाम क्या है?
Correct answer: D
Q. What is the specification of centre lathe marked ‘X’? | ‘X’ द्वारा केंद्र खराद का कौन सा विनिर्देश चिह्नित है?
Correct answer: A
Q. Which type taper is provided at the hollow end of the tailstock barrel/spindle? | टेलस्टॉक के स्लीव/बेरेल के खोखले सिरे पर कौन सा टेपर दिया जाता है
Correct answer: B
Q. Name the lathe accessory shown. | दिखाए गए लेथ एक्सेसरी का नाम बताइए।
Correct answer: B
Q. What is the purpose of the center shown in the figure? | चित्र में प्रदर्शित केंद्र का नाम क्या है?
Correct answer: D
Q. Where the driver pin is used? | ड्राईवर पिन कहाँ प्रयोग की जाती है?
Correct answer: A
Q. Which mechanism is used in three jaw chuck? | थ्री जॉ चक में किस मैकेनिज्म का उपयोग किया जाता है ?
Correct answer: A
Q. What is the name of the part of compound rest marked ‘X’? | ‘X’ द्वारा कंपाउंड रेस्ट के चिह्नित भाग का नाम क्या है?
Correct answer: D
Q. Which part of the lathe gives perpendicular movement to the tool? | लेथ का कौन सा भाग औजार को समलम्ब गति प्रदान करता है?
Correct answer: D
Q. What is the purpose of back gear unit in cone pulley headstock of a lathe? | लेथ के कोन पुली हेड स्टॉक की बेक गियर यूनिट का उद्देश्य क्या है?
Correct answer: D
Q. Which part is used to lock the carriage at any desired position? | कैरिज को किसी वांछित स्थान पर लॉक करने के लिए किस भाग का उपयोग किया जाता है?
Correct answer: C
Q. What is the inclined angle of dead center conical point? | डेड केंद्र के शंकुआकार भाग का झुकाव कोण कितना होता है?
Correct answer: B
Q. What is type of the lathe bed? | लेथ बेड का कौन सा प्रकार है?
Correct answer: D
Q. What is the name of the part ‘X’? | भाग ‘X’ का नाम क्या है?
Correct answer: D
Q. Which machine tool removes the metal from a revolving work piece with a stationery cutting tool? | स्टेशनरी कटिंग टूल के साथ घूमने वाले वर्क पीस से कौन सा मशीन टूल धातु निकालता है?
Correct answer: A
Q. Where will be using the angle plate and counter weight? | कोण प्लेट और काउंटर वजन का उपयोग कहां किया जता है?
Correct answer: A
Q. Which one of the below accessory has provided ‘U’ slot? | निम्न में से किस सहायक उपकरण में ʹUʹ स्लॉट्स दिए होते है?
Correct answer: C
Q. What is the name of part marked ‘X’ in cone pulley head stock of lathe? | ‘X’ द्वारा खराद के हेड स्टॉक की कोन पुली में कौन सा भाग चिह्नित है?
Correct answer: C
Q. What is the name of the part of tail stock marked ‘X’? | ‘X’ द्वारा टेल स्टॉक के चिह्नित भाग का नाम क्या है?
Correct answer: C
Q. Where the bend type lathe carrier is engaged? | बेंट टाइप लेथ कैरिएर कहाँ प्रयोग होता है?
Correct answer: C
Q. What is the name of the center? | केंद्र का नाम क्या है?
Correct answer: D
Q. Which part of lathe slides over the bed ways between headstock and the tailstock? | लेथ का कौन सा भाग हेड स्टॉक और टेल स्टॉक के बीच लेथ बेड पर स्लाइड करता है?
Correct answer: C
Q. Which one is used drive the work while turning between centre? | केंद्र के बीच टर्निंग समय वर्कपीस को चलाने के लिए किसका उपयोग किया जाता है?
Correct answer: D
Q. Which part of center lathe make angular movement? | केंद्र लेथ का कौन सा भाग कोणीय गति करता है?
Correct answer: D
Q. Which part of carriage is only for possible manual operation? | कैरिज के कौन से भाग का केवल हस्त परिचालन संभव है?
Correct answer: C
Module 4 Cutting tools & Measuring instruments
Q. What is the formula to calculate depth of cut for round job while turning? | टर्निंग करते समय राउंड जॉब के लिए कट की गहराई की गणना करने का सूत्र क्या है ?
Correct answer: A
Q. What is the name of the angle marked ‘X’? | x द्वारा चिह्नित किए गए कोण का नाम बताइये?
Correct answer: D
Q. Which instrument has zero parallax error? | कौन से उपकरण में शून्य पेरेलेक्स त्रुटी होती है?
Correct answer: A
Q. Which is the smallest measurement that is possible by vernier caliper? | कौन सा लघुत्तम माप वर्नियर कैलिपर से लिया जाना संभव है?
Correct answer: A
Q. What is the function of thumb lever of vernier caliper? | वर्नियर कैलिपर के अंगूठे लीवर का कार्य क्या है?
Correct answer: D
Q. What is the name of the tool? | औजार का नाम क्या है?
Correct answer: C
Q. What is the unit of cutting speed? | कटिंग स्पीड की इकाई क्या है?
Correct answer: A
Q. What is the formula for cutting speed(V)? | कटिंग स्पीड (V) का सूत्र क्या है?
Correct answer: B
Q. Which micrometer measure a sphere diameter exactly? | कौन सा माइक्रोमीटर एक गोले के व्यास को सटीक रूप से मापता है?
Correct answer: C
Q. What is the rpm of spindle for 50mm diameter workpiece and cutting speed 25 m/min? | 50 मिमी व्यास वर्कपीस और कटिंग स्पीड 25 मीटर/मिनट के लिए स्पिंडल का rpm क्या है?
Correct answer: A
Q. Which one is Non-Metallic tool material? | कौन सा गैर-धात्विक औजार सामग्री है ?
Correct answer: C
Q. Which is the example of ferrous tool material? | कौन सा फेरस औजार सामग्री का उदाहरण है?
Correct answer: A
Q. Which tool material have poor hardness property? | किस औजार सामग्री का कठोरता गुण निम्न है?
Correct answer: A
Q. What is the unit of feed? | फ़ीड की इकाई क्या है?
Correct answer: D
Q. What is the name of the angle marked ‘X’? | x द्वारा चिह्नित किए गए कोण का नाम बताइये?
Correct answer: A
Q. What is the use of tube micrometer? | ट्यूब माइक्रोमीटर का उपयोग क्या है?
Correct answer: A
Q. Name the part marked as ʹXʹ in vernier caliper. | वर्नियर कैलिपर में ʹXʹ के रूप में चिह्नित भाग का नाम बताए।
Correct answer: C
Q. Calculate the reading of the given metric outside micrometer? | बाह्य मीट्रिक माइक्रोमीटर का पठन ज्ञात कीजिये ?
Correct answer: A
Q. What is the pitch distance of a metric micrometer spindle thread? | मीट्रिक माइक्रोमीटर स्पिंडल चूड़ी की पिच कितनी होती है?
Correct answer: D
Q. What is the principle of micrometer? | माइक्रोमीटर का सिद्धांत क्या है?
Correct answer: B
Q. Which instrument is advantageous of absolute zero setting? | कौन सा उपकरण परम शून्य की व्यवस्था करने में लाभकारी है?
Correct answer: A
Q. Name the part marked as ‘X’ in depth micrometer. | गहराई माइक्रोमीटर में ’X’ के रूप में चिह्नित भाग को नाम बताए।
Correct answer: B
Q. What is the cutting speed if diameter=25mm and rpm(N)=1528? | कटिंग स्पीड क्या है यदि व्यास = 25 मिमी और rpm (N) = 1528 है?
Correct answer: B
Q. Which type of error the figure shows? | चित्र किस प्रकार की त्रुटि दर्शाता है?
Correct answer: A
Q. What is the least of an outside micrometer meter having 50 divisions on thimble and pitch of screw in 0.5mm? | किसी बाह्य माइक्रोमीटर का अल्पत्मांक क्या होगा जिसके स्लीव में 50 भाग हो तथा स्क्रू की पिच 0.5 mm ?
Correct answer: C
Q. Name the part marked as ʹXʹ. | Xʹ के रूप में चिह्नित भाग को नाम बताए।
Correct answer: A
Q. What is the instrument shown in figure? | चित्र में दिखाया गया उपकरण क्या है?
Correct answer: B
Q. What is the name of the part marked as ‘X’? | X ’के रूप में चिह्नित भाग का नाम क्या है?
Correct answer: C
Q. What is the purpose of side clearance given on turning tool? | खराद औजार पर साइड अवकाश का क्या उद्देश्य है ?
Correct answer: D
Q. How much distance is moved by spindle in one rotation of thimble of outside micrometer? | बाह्य माइक्रोमीटर में थिम्बल को एक पूरा चक्कर घुमाने पर स्पिंडल कितना आगे बढ़ता है?
Correct answer: C
Q. Which angle marked as ʹXʹ in parting off tool? | पार्टिंग ऑफ टूल में किस कोण को ʹXʹ के रूप में चिह्नित किया गया है?
Correct answer: B
Q. What is the name of instrument? | उपकरण का नाम क्या है?
Correct answer: A
Q. What is a vernier caliper? | वर्नियर कैलिपर क्या है?
Correct answer: C
Q. Which type of error the figure shows? | चित्र किस प्रकार की त्रुटि दर्शाता है?
Correct answer: A
Q. What is name of the part ʹXʹ? | भाग ʹXʹ का नाम क्या है?
Correct answer: D
Q. Why the carbide can NOT be used as solid bit? | क्यों कार्बाइड ठोस बिट के रूप में प्रयोग नहीं की जा सकती ?
Correct answer: B
Q. Which property avoid the breakage of cutting edge of tools? | कौन सा गुण औजार की कर्तन धार के टूटने से बचाव करता ?
Correct answer: C
Q. Which is the suitable instrument for fast checking the length of part? | किसी भाग की लम्बाई तुरंत जांचने में उचित उपकरण है?
Correct answer: A
Q. How to check the error in higher range (25-50 mm) of micrometer? | माइक्रोमीटर की उच्च श्रेणी (25-50 मिमी) में त्रुटि की जांच कैसे करें?
Correct answer: B
Q. What is the name of micrometer? | इस माइक्रोमीटर का नाम क्या है?
Correct answer: A
Q. What is ʺDʺ in cutting speed V=πDN/1000? | कटिंग स्पीड V=πDN/1000 में ʺDʺ क्या है?
Correct answer: A
Q. What is measured by the micrometer in the given figure? | दिए गए चित्र में माइक्रोमीटर द्वारा क्या मापा जाता है?
Correct answer: A
Q. What is the name of instrument? | उपकरण का नाम क्या है?
Correct answer: C
Q. Why the extreme care should be taken while handling vernier caliper? | वर्नियर कॉलिपर को संभालते समय अत्यधिक देखभाल क्यों की जानी चाहिए?
Correct answer: C
Q. Which is the material used in manufacture of frame for an outside micrometer? | बाह्य माइक्रोमीटर के फ्रेम के निर्माण में प्रयुक्त धातु कौन सी है?
Correct answer: C
Q. Which is an integrated part of beam of a vernier caliper? | वर्नियर कैलिपर के बीम का एक एकीकृत हिस्सा कौन सा है?
Correct answer: A
Q. Why the rake angle is provided? | रेक कोण क्यों प्रदान किया जाता है?
Correct answer: D
Q. What is the name of the tool? | औजार का नाम क्या है?
Correct answer: A
Q. What is the reading of vernier caliper? | वर्नियर कैलीपर का पठन क्या है?
Correct answer: B
Q. What is denoted by ‘V’ in the formula? | सूत्र में ʹVʹ द्वारा क्या दर्शाया गया है?
Correct answer: C
Module 5 Drills
Q. Which oil is mixed with water to improve Non-corrosive effect? | गैर-संक्षारक प्रभाव को सुधारने के लिए कौन सा तेल पानी में मिलाया जाता है?
Correct answer: C
Q. What is ratio of taper pin hand reamer? | टेंपर पिन हैंड रीमर का अनुपात क्या है?
Correct answer: A
Q. What is the name of the lubrication? | स्नेहन पद्धति का नाम क्या है??
Correct answer: B
Q. What is the name of the operation for making holes on work piece? | कार्य के टुकड़े पर छेद बनाने के लिए ऑपरेशन का नाम क्या है?
Correct answer: B
Q. Which part of the drill carries the coolant to the cutting edge? | ड्रिल का कौन सा भाग शीतलक को काटने वाले किनारे तक ले जाता है?
Correct answer: C
Q. What is the type of reamer? | रीमर का प्रकार क्या है?
Correct answer: C
Q. What is the part marked as X? | X के रूप में चिह्नित भाग क्या है?
Correct answer: C
Q. What will happen, if reamer is removing out in anticlockwise direction while reaming? | क्या होगा, अगर रीमर रेकिंग करते समय एंटीक्लॉकवाइज दिशा में निकाल रहे हैं?
Correct answer: D
Q. What is the name of the lubrication? | स्नेहन पद्धति का नाम क्या है?
Correct answer: A
Q. How the point angle should be to drill hard materials? | हार्ड मटेरियल को ड्रिल करने के लिए पॉइंट एंगल कैसा होना चाहिए?
Correct answer: D
Q. What is the name of the angle marked X? | चिह्नित X कोण का नाम क्या है?
Correct answer: B
Q. What is the bevelling angle for holes to be threaded? | छेद किए जाने वाले छेद के लिए बेवलिंग कोण क्या है?
Correct answer: B
Q. What is the part marked ‘X’? | x द्वारा चिह्नित भाग कौन सा है?
Correct answer: C
Q. What is the name of the part marked as X? | X के रूप में चिह्नित भाग का नाम क्या है?
Correct answer: B
Q. What is the purpose of reducing speed by 3/4th of turning while reaming? | रीमिंग के दौरान खराद की तुलना में 3/4 गति रखने का क्या उद्देश्य है?
Correct answer: B
Q. How the twist drill are designated? | ट्विस्ट ड्रिल को कैसे निर्दिष्ट किया जाता है?
Correct answer: A
Q. Which activity causes excessive wear and chattering of drill bit while drilling? | कौन सी गतिविधि ड्रिलिंग करते समय ड्रिल बिट के अत्यधिक घिसना और आवाज़ करने का कारण बनती है?
Correct answer: B
Q. What is the maximum size of parallel shank twist drill? | समानांतर शेंक मरोड़ ड्रिल का अधिकतम व्यास कितना होता है?
Correct answer: D
Q. What is the point angle of drill for drilling mild steel? | मृदु इस्पात की ड्रिलिंग के लिए ड्रिल का पॉइंट कोण क्या है?
Correct answer: C
Q. Which cutting fluid is used for turning copper? | किस कर्तन द्रव्य का प्रयोग तांबे की खराद करने में किया जाता है?
Correct answer: B
Q. Name the part marked as ʹXʹ. | Xʹ के रूप में चिह्नित भाग को नाम बताए।
Correct answer: D
Q. Which defect in drill bit causes over size the hole? | ड्रिल बिट में किस दोष के कारण छेद अधिक आकार का हो जाता है?
Correct answer: B
Q. Which type of drill is used for drilling brass? | किस प्रकार का ड्रिल पीतल में ड्रिल करने के काम आता है?
Correct answer: B
Q. What is the name of the lubricator? | स्नेहन औजार का नाम क्या है?
Correct answer: B
Q. What is the name of the part marked as X? | X के रूप में चिह्नित भाग का नाम क्या है?
Correct answer: D
Module 6 Fits & limits
Q. Which operation is used to increase the diameter of work slightly to get a press fit? | प्रेस फिट प्राप्त करने के लिए कार्य के व्यास को थोड़ा बढ़ाने के लिए किस ऑपरेशन का उपयोग किया जाता है?
Correct answer: A
Q. What is the maximum clearance for hole and Shaft ? | अधिकतम निकासी किसके लिए छेद और शाफ्ट है?
Correct answer: C
Q. What is the speed used for knurling? | नर्लिंग के लिए किस गति का प्रयोग किया जाता है?
Correct answer: B
Q. What is the name of the tool? | टूल का नाम क्या है?
Correct answer: B
Q. What is an advantage of mass production? | बड़े पैमाने पर उत्पादन का एक फायदा क्या है?
Correct answer: A
Q. What is the definition of fits? | फिट्स की परिभाषा क्या है?
Correct answer: D
Q. How many grades of tolerances are represented in BIS system? | बीआईएस प्रणाली में सहिष्णुता के कितने ग्रेड का प्रतिनिधित्व किया जाता है?
Correct answer: C
Q. How to indicate fundamental deviation of hole in BIS system? | बीआईएस सिस्टम में छेद के मूलभूत विचलन को कैसे इंगित करें?
Correct answer: B
Q. Calculate the upper deviation from the given data? | प्रस्तुत डाटा से उच्च विचलन ज्ञात कीजिये?
Correct answer: C
Q. What is the knurling pattern? | कौन सा नर्लिंग पैटर्न है?
Correct answer: C
Q. What is the purpose of knurling operation? | नर्लिंग संक्रिया का उद्देश्य क्या है?
Correct answer: A
Q. What type of fit is shown in figure? | आकृति में किस प्रकार का फिट दिखाया गया है?
Correct answer: D
Q. What is mass production? | बड़े पैमाने पर उत्पादन क्या है?
Correct answer: C
Q. Calculate the maximum limit of size from the given data 100+0.015-0.010? | 100+0.015-0.010 प्रस्तुत डाटा के माप की उच्चतम सीमा ज्ञात कीजिये
Correct answer: A
Q. Which system of limits and fits are followed in our country? | हमारे देश में लिमिट्स और फिट्स की किस प्रणाली का पालन किया जाता है?
Correct answer: A
Q. What is knurling pattern? | नर्लिंग पैटर्न क्या है?
Correct answer: C
Q. What is the system if the shaft is varied to set different class of fit? | यदि शाफ़्ट को विभिन्न श्रेणियों की फिट में बैठने के लिए परिवर्तित किया जाता है तो यह कौन सी पद्धति होगी?
Correct answer: C
Q. Which type of fit is obtain of the hole is bigger than the shaft? | छेद किस प्रकार का फिट है जो शाफ्ट से बड़ा है?
Correct answer: C
Q. How many fundamental deviation are in BIS system? | बीआईएस प्रणाली में कितने मौलिक विचलन हैं।
Correct answer: D
Q. What is the term if the difference between the maximum limit of size and minimum limit of size? | माप की उच्चतम सीमा और निम्नतम सीमा के अंतर को क्या कहते है?
Correct answer: C
Q. What is the maximum limit size of dimension ϕ25 +0.003 - 0.001? | आयाम की अधिकतम सीमा आकार ϕ25 +0.003 - 0.001 क्या है?
Correct answer: A
Q. What is actual deviation? | वास्तविक विचलन क्या है?
Correct answer: D
Q. What is Knurling? | नर्लिंग क्या है?
Correct answer: A
Q. What is 6 in the given expression of fit 30H7/g6? | फिट 30H7/g6 की अभिव्यक्ति में 6 क्या प्रदर्शित करता है?
Correct answer: D
Q. How external features of a component including which not cylindrical is designated as per BIS? | BIS के अनुसार किसी बेलन के बाहरी विशेषताओ को किसके बिना नामित नहीं किया जा सकता?
Correct answer: C
Module 7 Taper turning & Templates
Q. What is name of the element of screw thread marked as X? | X के रूप में चिह्नित स्क्रू थ्रेड के तत्व का नाम क्या है?
Correct answer: B
Q. What is the element of taper marked as X? | X के रूप में चिह्नित किए गए टेंपर का तत्व क्या है?
Correct answer: C
Q. A thread is represented as M12 x 1.5. What does represent the letter 12? | किसी चूड़ी को M12 x 1.5 द्वारा व्यक्त किया जाता है तो 12 क्या व्यक्त करेगा?
Correct answer: A
Q. What is marked as ʹXʹ? | Xʹ के रूप में चिह्नित क्या है?
Correct answer: B
Q. What is the name of the process? | प्रक्रिया का नाम क्या है?
Correct answer: C
Q. Why multi start thread is prepared in fly presses? | फ्लाई प्रेस में मल्टी स्टार्ट थ्रेड क्यों तैयार किया जाता है?
Correct answer: C
Q. How is the vernier height gauge generally specified? | सामान्य तौर पर वर्नियर हाइट गेज़ का विशिष्ठिकरण किसके द्वारा प्रदर्शित किया जाता है?
Correct answer: B
Q. What is the element of taper marked as X? | X के रूप में चिह्नित किए गए टेंपर का तत्व क्या है?
Correct answer: A
Q. Which standard tapers used in milling machine arbors? | मिलिंग मशीन आर्बर्स में कौन से मानक टेपर का उपयोग किया जाता है
Correct answer: D
Q. How is the “length of sine bar “specified? | ʺसाइन बार की लंबाईʺ कैसे निर्दिष्ट करते है?
Correct answer: A
Q. Which diameter the external threads are cut? | बाहरी धागे को किस व्यास में काटा जाता है?
Correct answer: C
Q. Identify the taper turning method. | टेपर टर्निंग की विधि पहचानिए।
Correct answer: A
Q. Read the angle? | कोण का पठन कीजिये?
Correct answer: B
Q. What is the reason for using dial indicator instead of scriber point in vernier height gauge? | वर्नियर हाइट गेज़ में स्क्राइबर बिंदु की अपेक्षा डायल इंडिकेटर उपयोग किए जाने का क्या कारण है?
Correct answer: A
Q. Which precision measuring instrument is a application of screw thread? | कौन सा सटीक मापक उपकरण स्क्रू थ्रेड का अनुप्रयोग है?
Correct answer: D
Q. What is the formula for taper angle used for taper turning attachment? | टेपर टर्निंग अटैचमेंट में टेपर कोण निकालने का सूत्र क्या है?
Correct answer: B
Q. What is the name of part marked as X? | X के रूप में चिह्नित भाग का नाम क्या है?
Correct answer: B
Q. What is the use of a sine bar? | साइन बार का क्या उपयोग है?
Correct answer: A
Q. Which one of the following taper turning method can be used for cutting internal taper with power feed? | निम्नलिखित में से कौन सा टेंपरिंग खराद पावर फीड के साथ आंतरिक टेपर काटने के लिए इस्तेमाल किया जा सकता है?
Correct answer: C
Q. Which taper is most commonly used as standard taper in industries? | उद्योगों में मानक शंकु के रूप में सबसे अधिक किस शंकु का उपयोग किया जाता है?
Correct answer: B
Q. What is the taper ratio for a taper length of 20 units the difference in diameter is one unit? | 20 इकाइयों की लंबाई के लिए टेपर अनुपात व्यास का अंतर एक इकाई क्या है?
Correct answer: B
Q. What is the name of the part marked as ‘x’ in the height gauge shown? | हाइट गेज़ के प्रदर्शित चित्र में ʹXʺ द्वारा चिह्नित बाग़ का नाम क्या है?
Correct answer: B
Q. What type of standard taper used on external taper of lathe spindle nose? | खराद स्पिंडल नाक के बाहरी शंकु पर किस प्रकार के मानक शंकु का उपयोग किया जाता है?
Correct answer: B
Q. Which method of taper turning the taper length is limited to movement of the top slide? | टेंपर की लंबाई को खराद करने वाले टापर की कौन सी विधि शीर्ष स्लाइड के संचलन तक सीमित है?
Correct answer: C
Q. What is the name of the bottom surface joining the two sides of adjacent thread marked as X? | X के रूप में चिह्नित समीपवर्ती थ्रेडों के दोनों पक्षों में शामिल होने वाली निचली सतह का नाम क्या है?
Correct answer: A
Module 8 Thread cutting & Gear calculation
Q. What is the name of screw thread element marked as ‘X’? | ‘X’द्वारा पेंच चूड़ी के चिह्नित तत्व का नाम क्या है?
Correct answer: B
Q. Which type of defect is marked as ‘X’? | ‘X’ द्वारा किस प्रकार का दोष चिह्नित किया गया है?
Correct answer: C
Q. Calculate the change gears to cut a worm of 0.35” lead on a lathe with a lead screw of 4TPI? | 0.35” लीड वला वर्म काटने के लिए वांछित चेंज गियर अनुपात की गणना कीजिये यदि लेथ के लीड स्क्रू 4 TPI का हो?
Correct answer: D
Q. What is thread element that determine the direction of rotation on screw thread? | चूड़ी का कौन सा तत्व है जो पेंच चूड़ी के घूर्णन की दिशा निर्धारित करता है?
Correct answer: D
Q. What is the tool life index of cemented carbide tool for turning high carbon steel? | सीमेंटेड कार्बाइड औजार से उच्च कार्बन इस्पात खराद करने पर औजार आयु सूचकांक का मान कितना होगा?
Correct answer: A
Q. What is 1.25 stands for a metric thread designated as M12 x 1.25? | M12 x 1.25 द्वारा नामित मीट्रिक चूड़ी में 1.25 क्या प्रदर्शित करता है?
Correct answer: D
Q. Which instrument has this type of measuring anvils? | किस उपकरण में मापन हेतु इस प्रकार की निहाई दी जाती है?
Correct answer: A
Q. How can measure the minor diameter of a external thread? | आंतरिक धागे के मामूली व्यास को कैसे माप सकते हैं?
Correct answer: A
Q. Calculate the change gear (driven gear) if driver is 50 teeth to cut 2.5mm pitch thread on a job by lathe having a lead screw of 5mm pitch? | 2.5 mm पिच वाली चूड़ी काटने के लिए वांछित चेंज गियर(ड्रिवेन गियर) की गणना कीजिये यदि लेथ के लीड स्क्रू की पिच 5 mm हो और ड्राईवर 50 दांतों का हो.
Correct answer: B
Q. Which type of thread is produced by tap and die? | टेप और डाई द्वारा किस प्रकार की चूड़ी उत्पादित की जाती है?
Correct answer: C
Q. Calculate the change gears necessary to cut a thread of 7/16” lead on a lathe with a lead screw of 4TPI? | 7/16” लीड वाली चूड़ी काटने के लिए वांछित चेंज गियर की गणना कीजिये यदि लेथ के लीड स्क्रू 4 TPI का हो?
Correct answer: A
Q. What is the name of the part marked as ʹXʹ in thread chasing dial mechanism? | थ्रेड चसिंग डायल तंत्र में X द्वारा चिह्नित भाग का नाम है?
Correct answer: D
Q. How tool life is expressed? | टूल लाइफ कैसे व्यक्त किया जाता है?
Correct answer: C
Q. Calculate the driven gear required to cut 4mm pitch thread is a lathe having lead screw of 4mm with driven gear of 60 teeth? | 4 मिमी पिच वाली चूड़ी काटने के लिए (ड्रिवेन गियर) की गणना कीजिये यदि लेथ के लीड स्क्रू की पिच 4 मिमी हो और ड्रिवेन गियर 60 दांतों का हो.
Correct answer: B
Q. What is formula of gear ratio for cutting threads? | चूड़ी कर्तन के लिए गियर अनुपात का सूत्र क्या है?
Correct answer: A
Q. How much percentage of cutting speed reduced to increase tool life two times? | टूल लाइफ को दो गुना बढ़ाने के लिए कटिंग स्पीड का कितना प्रतिशत कम किया गया है?
Correct answer: C
Q. How much the compound rest should be tilted for cutting metric thread by compound rest? | कंपाउंड रेस्ट द्वारा चूड़ी कर्तन के लिए उसे कितना तिरछा करना होगा?
Correct answer: B
Q. What is the name of the item marked as “X”? | “x” द्वारा चिह्नित वस्तु का नाम बताइये?
Correct answer: A
Q. What is the use of hand chaser? | हैण्ड चेसर का क्या उपयोग है?
Correct answer: B
Q. Which thread is recommended for pipe and pipe fittings? | पाइप और पाइप फिटिंग के लिए किस चूड़ी की अनुशंषा की जाती है?
Correct answer: C
Q. What is the thread form cut by using chasers? | कौन सा थ्रेड फॉर्म चेसर का प्रयोग करके बनाया जाता है?
Correct answer: B
Q. What is measured on internal thread? | आंतरिक चूड़ियों में क्या मापा जाता है?
Correct answer: B
Q. What is the shape of interchangeable anvils used in screw thread micrometer? | स्क्रू थ्रेड माइक्रोमीटर में विनिमयशील निहैयों का आकार होता है?
Correct answer: B
Q. Calculate the change gear (driver gear) if driven gear has 120 teeth to cut 3mm pitch on a job using lathe having 6 mm pitch lead screw? | 3 mm पिच वाली चूड़ी काटने के लिए वांछित चेंज गियर की गणना कीजिये यदि लेथ के लीड स्क्रू की पिच 6 mm हो और ड्रिवेन गियर 120 दांतों का हो.
Correct answer: B
Q. Which parameter of a thread is measured by three wire method? | तीन वायर प्रणाली द्वारा थ्रेड का कौन सा तत्व मापा जाता है?
Correct answer: D
Q. How metric chasing dial differ from British chasing dial? | मीट्रिक चेसिंग डायल ब्रिटिश चेसिंग डायल से किस तरह भिन्न है?
Correct answer: D
Q. Which part of screw thread micrometer is differ from an ordinary micrometer? | स्क्रू थ्रेड माइक्रोमीटर का कौन सा भाग साधारण माइक्रोमीटर से भिन्न होता है?
Correct answer: D
Q. Find the gears required to cut 4.5mm pitch on a lathe having a lead screw of 4 TPI. Gears available from 20 to 120 teeth by 5 teeth with a special gear of 127T. | 4.5 mm पिच वाली चूड़ी काटने के लिए उचित गियरों का चयन कीजिये यदि लेथ का लीड स्क्रू 4 TPI हो और गियर 20 से 120 तक 5 दांतों के अन्तराल पर तथा 127T वाला विशेष गियर उपलब्ध हो?
Correct answer: A
Q. What is marked as ‘Xʹ? | ‘x’ द्वारा किसे चिह्नित किया गया है?
Correct answer: C
Q. What is the depth of cut for 10TPI BSW thread? | 10TPI BSW चूड़ी में कट की गहराई क्या होगी?
Correct answer: A
Q. Which terms are needed to calculate tool life index? | औजार आयु सूचकांक ज्ञात करने के लिए किसकी जरूरत पड़ती है?
Correct answer: C
Q. What is the instrument shown in the figure? | चित्र में दिखाया यंत्र है?
Correct answer: B
Q. Calculate the driven gear to cut 2mm pitch on a job using a lathe having lead screw of 4mm pitch with driven gear 50 teeth? | 2 mm पिच वाली चूड़ी काटने के लिए ड्रिवेन गियर की गणना कीजिये यदि लेथ के लीड स्क्रू की पिच 4 mm हो और ड्रिवेन गियर 50 दांतों का हो.
Correct answer: C
Q. Identify the part marked as ‘X’ in a British chasing dial. | ब्रिटिश थ्रेड चसिंग डायल तंत्र में X द्वारा चिह्नित भाग का नाम है।
Correct answer: B
Q. What percentage of cutting speed is reduced for tool life doubling? | टूल लाइफ डबिंग के लिए कटिंग गति का कितना प्रतिशत कम होता है?
Correct answer: C
Q. Calculate the change gear ratio to cut a thread of 7/16” lead on a lathe with lead screw of 4 TPI? | 7/16” लीड वाली चूड़ी काटने के लिए वांछित चेंज गियर अनुपात की गणना कीजिये यदि लेथ के लीड स्क्रू 4 TPI का हो?
Correct answer: B
Q. Which is the method of thread measurement? | यह चूड़ी मापन की कौन सी पद्धति है?
Correct answer: C
Q. What is the formula for finding gear ratio for fractional pitch thread? | आंशिक पिच चूड़ी के लिए गियर अनुपात ज्ञात करने का सूत्र क्या है?
Correct answer: A
Q. What is the name of the part marked as ʹXʹ? | Xʹ के रूप में चिह्नित भाग का नाम क्या है?
Correct answer: B
Q. Which is the chip less method of thread production? | चूड़ी निर्माण की चिप रहित विधि कौन सी है?
Correct answer: B
Q. Which method of threading is used in mass production? | बृहत् उत्पादन में थ्रेडिंग की कौन सी विधि प्रयोग की जाती है?
Correct answer: D
Q. What is the criteria for the selection of interchangeable anvil of a screw thread micrometer? | स्क्रू थ्रेड माइक्रोमीटर के लिए विनिमयशील निहाई के चयन हेतु क्या मापदंड होगा?
Correct answer: C
Q. Which angle is provided on the metric screw thread micrometer anvil? | मीट्रिक स्क्रू थ्रेड माइक्रोमीटर की निहाई पर कितना कोण दिया जाता है?
Correct answer: A
Q. What is the purpose of using thread micrometer? | थ्रेड माइक्रोमीटर प्रयोग किए जाने का उद्देश्य क्या है?
Correct answer: A
Q. Which thread is used for general purpose fastening? | सामान्य फस्निंग कार्य के लिए किस चूड़ी का प्रयोग किया जाता है?
Correct answer: A
Q. Calculate the change gear required to cut 4mm pitch thread in a lathe having lead screw of 4mm (lathe stud gear driver has 50 teeth) | 4 मिमी के लेड स्क्रू वाले खराद में 4 मिमी पिच धागे को काटने के लिए आवश्यक परिवर्तन गियर की गणना करें (खराद स्टड गियर चालक के पास 50 दांत हैं)
Correct answer: B
Q. How many un-numbered divisions on the British chasing dial? | ब्रिटिश थ्रेड चसिंग डायल में बिना अंको वाले कितने विभाजन होते है?
Correct answer: B
Q. What is the name of operation? | संक्रिया का नाम क्या है?
Correct answer: C
Q. What are the uses of B.S.P thread? | B.S.P चूड़ी का क्या उपयोग है?
Correct answer: C
Q. What is the gear marked as ‘x’? | Xʺ द्वारा चिह्नित गियर है?
Correct answer: A
Module 9 Various forms of threads
Q. What is the name of thread? | चूड़ी का नाम क्या है?
Correct answer: B
Q. Which device uses buttress thread? | कौन सी युक्ति में बट्रेस चूड़ी का प्रयोग होता है?
Correct answer: C
Q. What is the thread depth of square thread SQ60x9? | SQ60x9 वर्गाकार चूड़ी की गहराई कितनी होगी?
Correct answer: A
Q. Which is the type thread? | चूड़ी का कौन सा प्रकार है?
Correct answer: D
Q. What is the angle of metric ACME thread? | मीट्रिक ACME चूड़ी का कोण कितना होता है?
Correct answer: B
Q. Which formula is used to find crest width of a buttress thread? | कौन से सूत्र से बट्रेस चूड़ी के क्रेस्ट की चौड़ाई ज्ञात की जाती है?
Correct answer: A
Q. What is formula for finding depth of BSW external thread? | BSW बाह्य चूड़ी की गहराई ज्ञात करने का सूत्र क्या है?
Correct answer: B
Q. What does BIS stand for? | BIS किसे व्यक्त करता है?
Correct answer: B
Q. Which formula is used to find depth of buttress thread? | कौन से सूत्र से बट्रेस चूड़ी की गहराई ज्ञात की जाती है?
Correct answer: D
Q. Which is the type of thread? | चूड़ी का कौन सा प्रकार है?
Correct answer: D
Q. Which is the element of thread? | चूड़ी का कौन सा तत्व है?
Correct answer: C
Q. Which one is the example for transmission of motion using thread? | चूड़ी का उपयोग करके गति के प्रसारण का कौन सा उदाहरण है
Correct answer: B
Q. Which type thread is used in lathe lead screw? | लेथ के लीड स्क्रू में कौन सी चूड़ी प्रयोग होती है?
Correct answer: D
Q. Calculate the flat width of 10 mm pitch buttress thread. | 10 mm पिच वाली बट्रेस चूड़ी के फ्लैट की चौड़ाई कितनी होगी।
Correct answer: A
Q. Which one is the use of thread? | चूड़ी का प्रयोग कौन सा है?
Correct answer: B
Q. What is the relationship between pitch and depth of a square thread? | वर्गाकार चूड़ी में पिच और चूड़ी की गहराई में क्या सम्बन्ध है?
Correct answer: B
Q. Which type of thread is used in screw jack spindle? | स्क्रू जैक के स्पिंडल में किस प्रकार की चूड़ी प्रयोग की जाती है?
Correct answer: C
Q. Which of the following is a modified form of square thread? | निम्नलिखित में से कौन सा वर्गाकार धागे का संशोधित रूप है?
Correct answer: B
Q. What is the width of the tool to cut square thread of 30 x 3 mm pitch? | 30 x 3 mm पिच की वर्गाकार चूड़ी काटने वाले औजार की चौड़ाई कितनी होगी?
Correct answer: B
Q. Which is the angle of buttress thread? | बट्रेस चूड़ी का कोण होता है?
Correct answer: B
Q. What is the minor diameter of screw thread SQ 62 x 10.8 with depth clearance of 0.12 mm? | SQ 62 x 10.8 वर्गाकार पेंच चूड़ी जिसका गहराई निकास 0.12 mm हो का लघु व्यास होगा?
Correct answer: B
Q. What is the minor diameter of Trapezoidal screw thread Tr 40 x 7 depth clearance of 0.01 mm? | Tr वर्ग धागा Tr 40 x 7 गहराई 0.01 mm की मामूली निकासी का मामूली व्यास क्या है?
Correct answer: A
Q. Which formula is used to find depth of ACME thread? | कौन से सूत्र से ACME चूड़ी की गहराई ज्ञात की जाती है?
Correct answer: A
Q. What is calculated by formula 0.75 x pitch? | सूत्र 0.75 x पिच द्वारा क्या ज्ञात किया जाता है?
Correct answer: D
Q. What is the use of thread? | चूड़ी का क्या प्रयोग होगा?
Correct answer: A
Module 10 Special job and Maintenance
Q. What is the representation of below symbol? | निन्म चिन्ह किसे प्रदर्शित करता है?
Correct answer: B
Q. What is the name of lubrication method? | स्नेहन पद्धति का नाम क्या है?
Correct answer: D
Q. What is the name of the center? | केंद्र का नाम क्या है?
Correct answer: B
Q. Which mechanism is used for converting linear motion into rotary motion in plunger dial gauge? | प्लंजर डायल गेज़ में कौन सा तंत्र रेखिक गति को घूर्णन गति में परिवर्तित करता है?
Correct answer: B
Q. What is the name of the lubricating system? | स्नेहन पद्धति का नाम क्या है?
Correct answer: A
Q. Which mandrels is NOT used in between lathe centers? | कौन सी मेन्ड्रेल केन्द्रों के बीच नहीं प्रयोग की जाती है?
Correct answer: B
Q. What is the material to hold the abrasive particles together in a grinding wheel? | एक पीस व्हील में अपघर्षक कणों को एक साथ रखने के लिए सामग्री क्या है?
Correct answer: C
Q. What term indicate actual size of the abrasive grain? | किस शब्दावली के द्वारा अपघर्षक के वास्तविक साइज़ को व्यक्त किया जाता है?
Correct answer: B
Q. What is the name of the lathe centre? | खराद केंद्र का नाम क्या है?
Correct answer: C
Q. What is the name of lathe accessory? | लेथ के इस सहायक उपकरण का नाम क्या है?
Correct answer: D
Q. What is the name of the center? | केंद्र का नाम क्या है?
Correct answer: D
Q. Which bonding material is not affected by water, acid or normal temperature? | कौन सी बंधक सामग्री जल, एसिड एवं सामान्य ताप से प्रभावित नहीं होती ?
Correct answer: A
Q. What type of taper provided on the shank of lathe center? | लेथ केंद्र की शंक में दिए गए टेपर का प्रकार है?
Correct answer: B
Q. Which wheel is used for grinding tough materials? | चीमड़ सामग्रीयों की घिसाईं के लिए कौन सी व्हील प्रयोग की जाती है?
Correct answer: B
Q. What is the name of part marked as ‘X’ in plunger type dial test indicator? | प्लंजर प्रकार के डायल परिक्षण सूचक के X द्वारा चिह्नित भाग का नाम क्या है?
Correct answer: D
Q. What is the name of chuck? | चक का नाम क्या है?
Correct answer: B
Q. What is the name of lathe accessory? | लेथ के इस सहायक उपकरण का नाम क्या है?
Correct answer: D
Q. Which mandrel is manufactured in order to reduce the number of mandrel? | कौन सी मेन्ड्रेल, मेंड्रेलों की संख्या कम रखने के उद्देश्य से बनायीं जाती है?
Correct answer: B
Q. What is the name of chuck that hardened steel sleeve having slits cut partly? | उस चक नाम क्या है जिसमे कठोरिकृत स्टील की आंशिक झिरी युक्त स्लीव लगी होती है?
Correct answer: B
Q. Which is used to support hollows end jobs? | किसका प्रयोग खोखले सिरे वाले कार्यों को पकड़ने में किया जाता है?
Correct answer: B
Q. Where the fatty oil is used? | चर्बी युक्त तेल का उपयोग कहाँ किया जाता है?
Correct answer: C
Q. What is the use of drive pin in drive plate? | ड्राइव प्लेट में ड्राइव पिन का उपयोग क्या है?
Correct answer: B
Q. What is the schedule of lubrication for lathe bed? | लेथ बेड के स्नेहन का कार्यक्रम होता है?
Correct answer: A
Q. What is the name of the lathe accessory? | लेथ के इस सहायक उपकरण का नाम क्या है?
Correct answer: C
Q. Which is the term used to express grinding wheels to hold the abrasive particle together? | ग्राइंडिंग व्हील में किस शब्दावली का प्रयोग अपघर्षक कणों को साथ बंधे रखने में किया जाता है?
Correct answer: D